Olympus-OM
[Top] [All Lists]

[OM] Fixed my battery on OM2S

Subject: [OM] Fixed my battery on OM2S
From: hogant@xxxxxxxxxxxxxx
Date: Sat, 22 Sep 2001 13:12:37 -0400
Cc: wkato@xxxxxxx, John Hermanson <omtech@xxxxxxxxx>

How I made a rechargeable remote battery for my OM2sp with an
on off switch that fits in a plastic 35mm film can -- Hank Hogan
<hogant@xxxxxxxxxxxxxx>

My OM2S is still a battery eater especially when I mount it on a
tripod and use a remote trigger for the winder.

Those batteries cost three dollars each. I think my local supplier's
batteries are out of date because they not last as long as the ones
John Hermanson put in my camera when I sent it to him for an overhaul.

I had some NiMh battery cells left over from my motor drive rebuild
project.  I tested with a V-O-M (meter) and some wires and determined
that three cells would supply the camera with the needed current
(two cells were not enough).

How to make the connector - I tried some water faucet valve seats,
close but not good enough.  I looked at my little tube of Kester
Rosin core solder - I wonder if the little cap would fit into the
battery receptacle of my OM2sp camera ? Voila, it's a perfect fit!
The little polyethylene cap fits snug into the battery well and
the little flange on the cap makes it flush with the bottom camera
plate !

Next, I took a black tie wire of the type that are used to close
large plastic bags, or bundle electrical cords and stripped of both
ends of the black plastic ribbon.  I test the electrical resistance
with the ohm meter. Yes, it will work fine !  Does the Winder II
fit one and operatate? Yes !  Polarity of the OM2SP ? Outside positive
inside negative - just look at the little silver oxide batteries.

Put a kink in the bared end of the tie wire and hang it up in the
spring that usually contacts the negative pole of the 357 battery.
Put a piece of scotch tape on it to hold in place as it comes out
of the hole in the plastice cap center.

For the outside positive connection I found a little screw that would
fit into that threaded hole in the side of the camera body intended
for the little black rubber grip that I have never seen in my life.
I soldered the positive lead into a small "solder-less" lug and put
some tiny lock washers on either side.

Okay, solder the connections to the tin of the three NiMh cells 
(like Frank van Lindert explained few years ago).

Put a Radio Shack style in-line power connector jack on the leads 
and an in-line plug into a hole that you melt in the plastic film
cannister lid.  On the other put a hole in for a micro on/off switch.

I works great and if the leads are long enough it can be placed 
in your pocket to keep warm for outdoor photography in the Winter.
It can also be attached to the camera strap with some thick rubber
bands with the long leads folded up.

My little transformer has a variable voltage switch with a connector
that fits into the plug mounted into the film can lid.

Okay now for the details: Kester Pocket-Pak rosin core solder with
Kester's exclusive Servi-tube dispenser (it has a little shirt pocket
clip like a ball point pen)  I purchased it for $1.49 at MarVac 
electronics in Pasadena, last year, I think.
There is an address on the tube: 515 Touhy Ave., Des Plainee, Illinois
zip code 60018

Now I've got my OM2sprogram working on a rechargeable battery !
I didn't spend anything because I already had all this stuff in my
electronics projects box of junk cannibalized from old radio equipment.

-- Hank Hogan <hogant@xxxxxxxxxxxxxx>

< This message was delivered via the Olympus Mailing List >
< For questions, mailto:owner-olympus@xxxxxxxxxxxxxxx >
< Web Page: http://Zuiko.sls.bc.ca/swright/olympuslist.html >


<Prev in Thread] Current Thread [Next in Thread>
Sponsored by Tako
Impressum | Datenschutz