Olympus-OM
[Top] [All Lists]

Re: [OM] (OM) related - Manfrotto/bogen tripod head adj.

Subject: Re: [OM] (OM) related - Manfrotto/bogen tripod head adj.
From: Chuck Norcutt <chucknorcutt@xxxxxxxxxxxxxxxx>
Date: Fri, 03 Sep 2010 21:15:21 -0400
Whoops!  My Manfrotto head isn't close by but I just saw a photo of a 
3047 head and that's not what I have.  But I'll see what I can do with 
this advice anyhow.  I did put some wheel bearing grease on the shaft 
once but that was many years ago.  Maybe some cleaning and a lube 
change.  :-)

Chuck Norcutt


Rick Beckrich wrote:
> Chuck, if one of the three 3/32 inch* socket head screws is tighter than the
> others,
> it will cause a bind like that. Also, a little focus mount grade grease
> will smooth the operation. I use wheel bearing grease (sparingly).
> 
>    *I'm sure they are metric screws, but asa was all I had here at the desk.
> 
> On Fri, Sep 3, 2010 at 8:48 AM, Chuck Norcutt <chucknorcutt@xxxxxxxxxxxxxxxx
>> wrote:
> 
>> Speaking of 3047 3-way heads.  Mine has always had a herky-jerky motion
>> in its up/down tilt motion.  Normally not a problem but in certain
>> positions it tends to sieze up and requires more than normal force to
>> get beyond the sticking point which, in turn, means overshooting the
>> desired set point.
>>
>> Anybody know how to deal with that?
>>
>> Chuck Norcutt
>>
>>
>> Ken Norton wrote:
>>> Just let me know if you need parts. I have several junk bin 3047 3-way
>> heads.
>>> ken
>>> www.zone-10.com
>>>
>>> On Friday, September 3, 2010, Brian Swale <bj@xxxxxxxxxxxxxxx> wrote:
>>>> Has anyone here done maintenance on a Bogen/Manfrotto 3047 3-way
>>>> head?
>>>>
>>>> I have one that I've been using for at least 20 years, and one aspect of
>> its
>>>> behaviour is starting to be irritating.
>>>>
>>>> The adjuster that controls left-right tilt has got built-in slop. No
>> matter how
>>>> tight the clamp screw is twisted, it will still flop one way or the
>> other, usually
>>>> at an inconvenient moment.
>>>>
>>>> At the forward end of the shaft for this adjustor is an aluminium plate
>> with
>>>> the logo etc and a compass rose going from -30 to + 90 degrees.
>>>>
>>>> Since there is no possible way in from the side facing the camera, I
>> suspect
>>>> that I need to take this aluminium plate off (faces the photo subject)
>> to
>>>> investigate and find out the cause of the sloppy behaviour.
>>>>
>>>> Probably it should be removed with a sharp knife or a wood chisel.
>>>>
>>>> Is this the way to do it, and will this facing plate come out unscathed?
>>>>
>>>> All & any advice gratefully received.
>>>>
>>>> Brian Swale.
>>>> --
>>>> _________________________________________________________________
>>>> Options: http://lists.thomasclausen.net/mailman/listinfo/olympus
>>>> Archives: http://lists.thomasclausen.net/mailman/private/olympus/
>>>> Themed Olympus Photo Exhibition: http://www.tope.nl/
>>>>
>>>>
>> --
>> _________________________________________________________________
>> Options: http://lists.thomasclausen.net/mailman/listinfo/olympus
>> Archives: http://lists.thomasclausen.net/mailman/private/olympus/
>> Themed Olympus Photo Exhibition: http://www.tope.nl/
>>
>>
-- 
_________________________________________________________________
Options: http://lists.thomasclausen.net/mailman/listinfo/olympus
Archives: http://lists.thomasclausen.net/mailman/private/olympus/
Themed Olympus Photo Exhibition: http://www.tope.nl/

<Prev in Thread] Current Thread [Next in Thread>
Sponsored by Tako
Impressum | Datenschutz